|
|
|
|
Stubbs Welding Rocksliders. If you are looking for some additional information and specific vehicle install photos, take a look at the Stubbs Welding Website.
For pictures of sliders installed on the various vehicle and in use click these links:
Sliders Installed - Our Customers
Standard Rocksliders: These are entry level rock sliders for people that occasionally go off-road or are looking for a running board replacement. If you plan on rock crawling we highly suggest you look at the models with the rear kick feature which actually pushes the vehicle away from danger. This model while protecting your rocker panels, does not push the vehicle over.
This product is made with 1.5" diameter CREW (Cold Rolled Electric Welded) .120" wall round tubing. The sliders will be delivered in an unfinished/unpainted state, but are 100% ready to be welded to your vehicles frame. No further modifications are required. Just clean the paint off the frame, clamp the sliders to the vehicle and weld away. No legs to be cut and fit, no further fabrication required, this product is 100% ready to be installed upon arrival. This saves YOU a ton of money and time with your local fabricator/welder at the time of install. The exception is the front leg on the 1979-1995 models will be shipped long and then need to be cut to fit as there was a lot of production variance with those frames back in the day. The scab plates will be included and are already installed on all of the other legs (79-95) and welded on all of the other models (96+) at the time the sliders are built. Saving you even more installation cost and time.
Available for the following vehicles:
Standard
1984-2007 Toyota 4Runners
1979-2004 Pickup Truck/Tacoma: Regular Cab
1984-2004 Pickup Truck/Tacoma: Extra/Double Cab
2000-2006 Tundra: Regular/Extra/Double Cab
2000-2006 Tundra: Double Cab
2005+ Tacoma:
Regular/Extra/Double Cab Short bed
2005+ Tacoma: Double Cab long bed
UPS Ground shipping is additional.
Standard SKO (Single Kick Out) Rocksliders: This model does have a kick out to help protect your vehicle and assist in climbing up into a pickup bed or accessing your roof. Since the end of the slider does taper back in at the very end, this model does not offer the ultimate protection of our "Rubicon" sliders. It would be considered something in the middle between the Standard and the Rubicon versions. It will help push your vehicle over, but then does taper back in so the truck could slide back up against the rock as you pull forward. For serious rock crawling we would suggest the Rubicon model.
This product is made with 1.5" diameter CREW (Cold Rolled Electric Welded) .120" wall round tubing. The sliders will be delivered in an unfinished/unpainted state, but are 100% ready to be welded to your vehicles frame. No further modifications are required. Just clean the paint off the frame, clamp the sliders to the vehicle and weld away. No legs to be cut and fit, no further fabrication required, this product is 100% ready to be installed upon arrival. This saves YOU a ton of money and time with your local fabricator/welder at the time of install. The exception is the front leg on the 1979-1995 models will be shipped long and then need to be cut to fit as there was a lot of production variance with those frames back in the day. The scab plates will be included and are already installed on all of the other legs (79-95) and welded on all of the other models (96+) at the time the sliders are built. Saving you even more installation cost and time.
Available for the following vehicles:
Standard SKO
1984-2007 Toyota 4Runners1979-2004 Pickup Truck/Tacoma: Regular Cab
1984-2004 Pickup Truck/Tacoma: Extra/Double Cab
2000-2006 Tundra: Regular/Extra/Double Cab
2000-2006 Tundra: Double Cab
2005+ Tacoma: Regular/Extra/Double Cab Short bed
2005+ Tacoma: Double Cab long bed
UPS Ground shipping is additional.
Deluxe Rocksliders: These are built the same as the Standard Model except for the inner tube is 2"x2" square. The same suggestions and recommendations for the Standard Model would apply to this model as well.
This product is made with 1.5" diameter CREW (Cold Rolled Electric Welded) round tubing and 2"x2" square tubing. Both are .120" wall. The sliders will be delivered in an unfinished/unpainted state, but are 100% ready to be welded to your vehicles frame. No further modifications are required. Just clean the paint off the frame, clamp the sliders to the vehicle and weld away. No legs to be cut and fit, no further fabrication required, this product is 100% ready to be installed upon arrival. This saves YOU a ton of money and time with your local fabricator/welder at the time of install. The exception is the front leg on the 1979-1995 models will be shipped long and then need to be cut to fit as there was a lot of production variance with those frames back in the day. The scab plates will be included and are already installed on all of the other legs (79-95) and welded on all of the other models (96+) at the time the sliders are built. Saving you even more installation cost and time.
Available for the following vehicles:
Deluxe
1984-2007 Toyota 4Runners
1979-2004 Pickup Truck/Tacoma: Regular Cab
1984-2004 Pickup Truck/Tacoma: Extra/Double Cab
2000-2006 Tundra: Regular/Extra/Double Cab
2000-2006 Tundra: Double Cab
2005+ Tacoma: Regular/Extra/Double Cab Short bed
2005+ Tacoma: Double Cab long bed
UPS Ground shipping is additional.
Ultimate SKO (Single Kick Out) Rocksliders: This is a Heavy Duty/Severe Service Rock Slider with a single rear kick out. This is a rock slider that you would want to use for rock crawling. It is built from even heavier gauge metal the other models and is designed to take an extreme beating. It does have a rear kick to push your vehicle over and protect it as much as possible from damage.
This product is made with 1.5" diameter CREW (Cold Rolled Electric Welded) round tubing and 2"x2" square tubing. Both are .120" wall. The legs are made from 1.5"x1.5" square tubing with a wall thickness of .188 (3/16"). The sliders will be delivered in an unfinished/unpainted state, but are 100% ready to be welded to your vehicles frame. No further modifications are required. Just clean the paint off the frame, clamp the sliders to the vehicle and weld away. No legs to be cut and fit, no further fabrication required, this product is 100% ready to be installed upon arrival. This saves YOU a ton of money and time with your local fabricator/welder at the time of install. The exception is the front leg on the 1979-1995 models will be shipped long and then need to be cut to fit as there was a lot of production variance with those frames back in the day. The scab plates will be included and are already installed on all of the other legs (79-95) and welded on all of the other models (96+) at the time the sliders are built. Saving you even more installation cost and time.
Available for the following vehicles:
1984-2007 Toyota 4Runners
1979-2004 Pickup Truck/Tacoma: Regular Cab
1984-2004 Pickup Truck/Tacoma: Extra/Double Cab
2000-2006 Tundra: Regular/Extra/Double
Cab
2005+ Tacoma: Regular/Extra/Double
Cab
UPS Ground shipping is additional.
Rubicon Single Kick Rocksliders: Same as the Double Kick Sliders listed below, but with a round front and the ultimate rear kick.
Available for the following vehicles:
1984-2007 Toyota 4Runners
1979-2004 Pickup Truck/Tacoma: Regular Cab
1984-2004 Pickup Truck/Tacoma: Extra/Double Cab
2000-2006 Tundra: Regular/Extra/Double
Cab
2005+ Tacoma: Regular/Extra/Double
Cab
UPS Ground shipping is additional.
Rubicon Double Kick Rocksliders: This design is the best rock slider we could possibly come up with. It is available with a round outer tube or an all square version with kick outs that flow into the tires on both ends. If you want the best rock slider money can buy, this is it. The kicks will push your vehicle away from the rocks going forward or backwards. These sliders are TIG (Tungsten-Inert-Gas) welded which is typically used in Aerospace industry. Nothing is spared when building these sliders, all the heavies materials and the most effective welding techniques are employed. If you wheel your truck hard or rock crawl, there is no substitute for these Rocksliders.
This product is made with 2" diameter CREW (Cold Rolled Electric Welded) round tubing and/or 2"x2" square tubing. Both are .120" wall. The legs are made from 1.5"x1.5" square tubing with a wall thickness of .188 (3/16"). The sliders will be delivered in an unfinished/unpainted state, but are 100% ready to be welded to your vehicles frame. No further modifications are required. Just clean the paint off the frame, clamp the sliders to the vehicle and weld away. No legs to be cut and fit, no further fabrication required, this product is 100% ready to be installed upon arrival. This saves YOU a ton of money and time with your local fabricator/welder at the time of install. The exception is the front leg on the 1979-1995 models will be shipped long and then need to be cut to fit as there was a lot of production variance with those frames back in the day. The scab plates will be included and are already installed on all of the other legs (79-95) and welded on all of the other models (96+) at the time the sliders are built. Saving you even more installation cost and time.
 |
 |
Available for the following vehicles:
1984-2007 Toyota 4Runners
1979-2004 Pickup Truck/Tacoma: Regular Cab
1984-2004 Pickup Truck/Tacoma: Extra/Double Cab
2007+ FJ Cruiser
UPS Ground shipping is additional.
FJ Cruiser Ultimate SKO Rocksliders: 100% Bolt on! These sliders are built the same as our severe duty models above but are designed specifically for the Toyota FJ Cruiser and are completely bolt on. Metric 10.9 Hardware is included as well. The mounting surface on these sliders is a "C" channel up against he frame for ultimate strength.
This product is made with 1.5" diameter CREW (Cold Rolled Electric Welded) round tubing and 2"x2" square tubing. Both are .120" wall. The legs are made from 1.5"x1.5" square tubing with a wall thickness of .188 (3/16"). The sliders will be delivered in an unfinished/unpainted state, but are 100% ready to be bolted to your vehicles frame with the supplied hardware.
Available for the following vehicles:
2007+ FJ Cruiser,
Ultimate SKO
2007+ FJ Cruiser, Deluxe
UPS Ground shipping is additional.
To order Stubbs Welding Rocksliders, contact Sonoran Steel at:
Steve@SonoranSteel.com or 480-201-4139
